Friday, March 29, 2024

Digital Soil Moisture Meter

T.K. Hareendran is founder and promoter of TechNode Protolabz

Fig. 1: Soil moisture sensor head
Fig. 1: Soil moisture sensor head

efy tested sani theoA digital soil moisture meter is used for indicating the water content of a given soil sample. As crop production requires water at different stages and in different amounts, it is important to measure soil moisture from time to time to know its status.

The digital soil moisture meter circuit presented here, for monitoring the soil moisture content in irrigation farms, is an electronic device that measures soil moisture content accurately and precisely. It measures the resistance of flow of the electric current between two metallic probes. These probes act as sensor elements that register moisture and change it into an electric value. This value is further processed into information in the form of an electronic display.

Digital soil moisture meter circuit

Fig. 2: Circuit diagram of the digital soil moisture meter
Fig. 2: Circuit diagram of the digital soil moisture meter

Front-end of the digital soil moisture meter is a simple soil moisture sensor head, built around a few easily-available parts. Working of the sensor head electronics is self-explanatory, so just follow the conceptual drawing (and schematic drawing) shown in Fig. 1 to proceed with its construction.

Fig. 3: Live LCD screen in author’s prototype
Fig. 3: Live LCD screen in author’s prototype
Fig. 4: PCB pattern of the soil moisture meter
Fig. 4: PCB pattern of the soil moisture meter

Complete circuit diagram of the soil moisture meter is shown in Fig. 2. After construction of the sensor head, power it off a regulated 5V DC supply.

Fig. 5: Component layout of the PCB
Fig. 5: Component layout of the PCB
Fig. 6: Screenshot of Arduino IDE
Fig. 6: Screenshot of Arduino IDE

Insert the probes of the sensor head into the soil to determine its moisture content, and carefully adjust the preset VR1 so that voltage just above 3V is available at pin A1 of Arduino (Board1) if the soil is wet enough.

- Advertisement -

Construction and testing

Repeat the calibration process with randomly-collected soil samples ranging from very dry to very wet, depicting different moisture levels. Re-tune VR1,parts list if necessary, until you are satisfied with the calibration process. (Note that the depths of penetration of the probes into the soil affect calibration.) Link the sensor head to the rest of the hardware to complete the project.
Rest of the hardware is a combination of Arduino microcontroller and a solid-state display panel. For compactness, Arduino Nano V3 platform is used to drive the 16×2 LCD panel.

Though a 6V battery pack is used to energise the hardware setup, you can also use external  DC power in 7V – 12V range at VIN of Board1 without any problem. The 10-kilo-ohm preset (VR2) is included to adjust the contrast level of the display. Similarly, the 100-ohm resistor (R2) limits the operating current of the backlight lamp inside the display panel.

After building the hardware, load the code (sketch) to the microcontroller, that is, copy the sketch, paste it into Arduino IDE, compile and upload. It should work at first try and you should get the message shown in Fig. 3 on your LCD screen.

- Advertisement -

A single-side PCB for the soil moisture meter is shown in Fig. 4 and its component layout in Fig. 5. Enclose the PCB in a suitable box.

Components description

Connectors CON1, CON2, CON3 and CON4 are for connecting the sensor probe, analogue input, board1 and LCD1, respectively.

These days the cheapest USB-to-serial chip on the market is CH340G, and most of the reasonably-priced Arduino-compatible Nano V3 microcontroller modules (with USB mini-B connection) are wired with CH340G USB-to-serial chip on board.

Arduino Nano V3 can be powered via the USB mini-B connection or 5V regulated external DC power supply at 5V pin on Board1.

CH340G chip on Arduino Nano V3 is only powered if the board is being powered over USB. As a result, when running on external (non-USB) power, 3.3V output (supplied by CH340 chip) is not available. Arduino Nano V3 can be programmed with Arduino software (IDE). Just select Arduino Duemilanove or Nano w/ATmega328 from Tools Board Menu, as shown in Fig. 6.

Driver for Arduino Nano V3 clone is available here.

Lab note. The project was tested at EFY using Arduino Uno board.

Download PCB and Component Layout PDFs: CLICK HERE

Download Source Code: CLICK HERE


Feel interested? Check out other electronics projects.

5 COMMENTS

SHARE YOUR THOUGHTS & COMMENTS

Electronics News

Truly Innovative Tech

MOst Popular Videos

Electronics Components

Calculators