It is a simple circuit that can be programmed to turn on household appliances like lights, fans, TV sets, music systems, etc exactly at a preset time and turn off at another preset time automatically, thereby saving on electricity. You can turn the appliance ‘on’ or ‘off’ with the clap of your hand, if so desired, without having to touch the unit physically.
Appliance timer circuit
This transistor based appliance timer circuit uses readily available components, is easy to assemble as well as inexpensive, and can be programmed to switch on/off a load from one second to 100 hours in advance. To make the circuit cost-effective as well as simple to construct, a general purpose digital clock is incorporated as the basic timing device. The alarm output of the clock is used to toggle the output power supply for switching an appliance ‘on’ or ‘off.’
Transistors T6 and T7 are configured as a bistable flip-flop that has two stable states. Transistor T7 will be in cut-off mode corresponding to transistor T6 in conduction mode, and vice versa. When transistor T6 conducts, its collector potential is very near to the emitter potential, i.e., ground, and therefore there is no base current to transistors T7 through R6. Thus, transistor T7 is in cut-off state. The collector of T7 is above ground potential and the current flows through resistors R7 and R13 to maintain the base current of T6. Thus, T6 remains in conduction state and T7 in cut-off state indefinitely.
Now, if a voltage pulse is applied to the base of transistor T7 from some external source, a momentary base current will trigger it into conduction and its collector potential will come down to near ground potential. Thus, the current flowing through resistor R13 will pass through the collector of T7 and there will be no current through R7, making T6 go into cut-off state and thereby raising the collector potential of T6 to some positive value. This, in turn, will keep T7 conducting. Now the base current of T7 will pass through resistors R14 and R6. This state will sustain until some external voltage is applied to the base of T6.
The external voltage pulse (for switching) is taken from two sources, the alarm output of a clock or the sound picked up by condenser microphone ‘M’ after proper amplification by transistors T1, T2 and T3.
Since most of the digital clocks give out negative pulses to the buzzer (whose other end is directly connected to the positive terminal of the battery), a reverse diode (D8) and a pnp transistor (T10) are used at this stage. The negative pulses are rectified by D8 and filtered by C9 to supply a steady base current of T10. Otherwise, the output will become noisy because of the pulsating nature of the alarm. (If the clock gives out positive pulses, T10 can be replaced with an npn transistor like BC547. Diode D8 has to be reversed and R18 has to be connected between the base of T10 and ground.)
The external voltage pulse is fed at the common emitter of transistors T4 and T5 through capacitor C8. When the alarm starts (sending negative voltage pulses), capacitor C9 discharges through D8 and, at the same time, charges through R19, thus triggering the base current of T10. The emitter current of T10 charges capacitor C8, which passes through the emitter of either T4 or T5 depending on their bias.
When T6 is conducting, T4 is forward biased and the voltage pulse is fed at the base of T7, bringing T7 into conduction and T6 into cut-off mode. This makes T5 forward-biased and T4 reverse-biased. The next voltage pulse, either through T10, D1 or D2 corresponding to the clock alarm, clap sound or operation of the reset switch, sends a base current of T6 through the emitter of T5 and the output changes over.
When clap switch is not required, S2 can be turned off. S3 is the reset switch (push-to-on type), which is used to toggle the output between ‘on’ and ‘off’ states. R10-C7 and R8- C6 are parallel paths to R7 and R6 for quick switch over of the bistable latch.