Home Engineering Projects For You 1001+ Electronics Projects For You

Vibration Activated Smart CRO Probe

By K. Murali Krishna. He is a former faculty of Aditya Engineering College, Surampalem. Presently, he is working as a telecom technical assistant, BSNL Rajahmundry, Andhra Pradesh

smart CRO probe
Fig. 1: Author’s prototype: (a) internal part of the prototype, (b) prototype with CRO and (c) vibration sensor with CRO probe

Here is a simple, low-cost, energy-saving and device-saving circuit for an electronics lab, service centre, electronics workshop, or wherever a CRO is in use. A vibration sensor attached to a smart CRO probe senses motion when you pick up the probe and turns on the CRO. It turns the CRO off when the probe is idle for a specified amount of time.

Generally, in a repair station, a CRO is used for a very short time. But in most cases, the user fails to switch off the CRO immediately after use. The service engineer mostly concentrates on faults rather than noticing whether the CRO is on or off. This results in wastage of power, reduction in CRO lifetime and leads to phosphorus burn in the cathode ray tube (CRT) due to electrons hitting the screen on the same spot for a very long time, which again leads to reduction of CRT lifetime. Fig. 1 shows the author’s prototype.

Fig. 1: Author’s prototype: (a) internal part of the prototype, (b) prototype with CRO and (c) vibration sensor with CRO probe
Fig. 2: Block diagram of the vibration activated smart CRO probe

The block diagram of the vibration activated smart CRO probe is shown in Fig. 2. A vibration sensor fixed on the CRO probe senses the vibrations picked up by the probe. This vibration signal is sensed, stored in a capacitor, compared with a reference voltage and fed to the relay driver to switch on the CRO. An additional circuitry is provided to switch off the CRO and give an audio acknowledgement in the form of a beeping sound.

The circuit diagram of the vibration activated smart CRO probe is shown in Fig. 3. It is built around bridge rectifier DB107 (BR1), vibration sensor HDX-2NC connected across connector CON2, quad comparator LM324 (IC1), 1N4148 and 1N4007 diodes (D1 and D2), relay driver transistor BC547 (T1), 12V single-changeover relay (RL1) and a few other components.

Smart CRO probe circuit

As shown in Fig. 3, the circuit is built around IC LM324, which is a low-cost, quad operational amplifier (with four op-amps). Op-amps in this circuit are configured in comparator and inverted-buffer modes.

Here, HDX-2NC, a normally-closed vibration sensor is used. A vibration sensor is a small two-terminal component connected across connector CON2 in series with resistor R1. Point A in the circuit is connected to pin 3 of IC1, which is its non-inverting terminal. Under normal conditions, point A is connected to ground via sensor HDX-2NC. During vibration, its contact opens for a very small amount of time.

Op-amp A1 acts as an input comparator. Resistors R2 and R3 act as potential dividers and produce around 1.2V at point B in the circuit. When there is vibration, 12V is produced at the non-inverting terminal of op-amp A1, which is greater than 1.2V at its inverting terminal. As a result, around 12V is produced at the output of A1. This is indicated by the glowing of vibration-sense indicator LED1.

The 12V produced at output of A1 charges capacitor C2 via diode D1. D1 allows the flow of current in only one direction, that is, from op-amp A1 to capacitor C2. Whenever there is a vibration, C2 charges to the maximum voltage and slowly discharges through resistor R9.

Maximum discharge time of C2 is around 30 minutes. Potmeter VR1 is used to set delay. Op-amp A2 is configured as a comparator, which compares the capacitor voltage against the set potmeter voltage. When C2 discharges, voltage decreases at the non-inverting terminal of A2. When voltage at C2 (pin 5 of A2) decreases beyond the set voltage (at pin 6 of A2), output of A2 at its pin 7 goes low. Output of A2 is connected to relay driver transistor T1.

Fig. 3: Circuit diagram of the vibration activated smart CRO probe
Fig. 4: PCB pattern of the vibration activated smart CRO probe
Fig. 5: Component layout of the PCB

Download PCB and component layout PDFs: click here

Fig. 6: Proposed front panel

When A2 output is high, relay RL1 energises and the CRO gets AC mains power supply via relay contacts to operate it. At the same time, the CRO-on indicator LED2 glows.

On time of the CRO can be set as per requirement using VR1. With a small voltage set via VR1 at inverting terminal pin 6 of A2, greater will be the delay. Similarly, with more voltage set, smaller will be the delay.



Please enter your comment!
Please enter your name here

Exit mobile version