Phase Angle Control Of SCR Using AT89C51

A. M. Bhatt


Silicon-controlled rectifiers (SCR) are solidstate semiconductor devices that are usually used in power switching circuits. SCR controls the output signal by switching it ‘on’ or ‘off,’ thereby controlling the power to the load in context. The two primary modes of SCR control are phase-angle fired—where a partial waveform is passed every half cycle—and zerocrossing fired—where a portion of the complete waveforms is passed to regulate the power. In the phase angle controller, the firing pulse is delayed to turn on the SCR in the middle of every half cycle. This means that every time a part of an AC cycle is cut, the power to the load also gets cut. To deliver more or less power to the load, the phase angle is increased or decreased, thereby controlling the throughput power.

There are several ways to control the firing angle of SCR. This article describes a microcontroller AT89C51-based phase angle controller. A microcontroller can be programmed to fire SCR over the full range of half cycles—from 0 to 180°—to get a good linear relationship between the phase angle and the delivered output power.

Some of the features of this microcontroller-based phase angle controller for SCR are:

  1. Utilises the zero-crossing detector circuit
  2. Controls the phase angle from 0–162°
  3. Displays the phase angle on an LCD panel
  4. LED indicators are used for displaying the status of SCR
  5. Increases or decreases the phase angle with intervals of 18°

Basically, the zero-crossing detector circuit interrupts the microcontroller after every 10 ms. This interrupt commands the microcontroller to generate some delay (in the range of 1ms to 9 ms). The user can increase or decrease the delay in intervals of 1 ms using switches. the SCR is then fired through the opto-coupler. This repeats after every 10 ms.

Phase angle controller circuit

The complete circuit is divided into two sections:

  1. The zero-cross detector section
  2. The control section
Fig.1: Power supply and zero-crossing detector circuits

The zero-cross detector section

Fig.1 shows the circuit diagram of the zero-crossing detector and the power supply. The main sections of the circuit are a rectifier, regulated power supply and zero-crossing detector. The 230V AC mains is stepped down by transformer X1 to deliver the secondary output of 9V, 500 mA. The transformer output is rectified by a full-wave bridge rectifier comprising diodes D1 through D4 and then regulated by IC 7805 (IC3). Capacitors C2 and C3 are used for bypassing the ripples present in the regulated 5V power supply. A capacitor above 10μF is connected across the output of the regulator IC, while diode D6 protects the regulator IC in case their input is short to ground. LED5 acts as the power-on indicator and resistor R5 limits the current through LED5.

This regulated 5V is also used as biasing voltage for both transistors (T1 and T2) and the control section. A pulsating DC voltage is applied to the base of transistor T1 through diode D5 and resistors R1 and R2. When the pulsating voltage goes to zero, the collector of transistor T1 goes high. This is used for detecting the pulse when the voltage is zero. Finally, the detected pulse from ‘C’ is fed to the microcontroller of the control section.

Fig.2: Circuit diagram of phase angle controller of SCR using AT89C51

The control section

Fig.2 shows the circuit diagram of the control section for the phase angle controller of SCR. It comprises a microcontroller AT89C51, opto-coupler MCT2E, LCD module and a few discrete components. Port 0 (P0.0 through P0.7) of AT89C51 is used for interfacing data input pins D0 through D7 of the LCD module.Port pins P2.6, P2.5 and P2.7 of the microcontroller control the registers select (RS), read/write and enable (E) input pin of the LCD module, respectively. Preset VR1 is used for controlling the contrast of the LCD module. Push-to-on switches S1, S2 and S3 are connected with the pins P1.0, P1.1 and P1.2 through diodes D9, D10 and D11, respectively. External interrupt pin (P3.2) of the microcontroller is connected to S1, S2 and S3 through D12, D13 and D14, respectively. The role of different switches is shown in Table I.

The output of the zero-crossing detector from ‘C’ is fed to the external interrupt pin (P3.3) of the microcontroller.



Please enter your comment!
Please enter your name here