Thursday, December 12, 2024

STK435 IC-Based Stereo Amplifier

- Advertisement -
efy test

This stereo AF amplifier uses the STK435 IC, a highly popular choice due to its simplicity. The STK435, with its 15-pin configuration, requires only a few external components, such as electrolytic and ceramic capacitors and resistors.

With a 12V DC power supply, the amplifier delivers approximately 7 watts to an 8-ohm speaker, offering excellent audio quality. The author’s prototype is shown in Fig. 1.

Parts List
Semiconductor:
IC1 (IC1A, IC1B): 15-pin STK435 stereo amplifier IC
Resistors (All 1/4-watt, ±5% Carbon)
R1, R15: 1 kΩ
R2, R12, R4, R14: 220 kΩ
R3, R13: 390 kΩ
R5: 100 Ω
R6, R11: 120 Ω
R7, R9: 4.7 Ω
R8, R10: 12 kΩ
Capacitors
C1, C13: 470 pF ceramic disk
C2, C12: 0.47 µF, 25V electrolytic
C3, C11: 10 µF, 25V electrolytic
C4, C9: 220 µF, 25V electrolytic
C5, C10: 47 µF, 25V electrolytic
C6, C7: 1000 µF, 25V electrolytic
C8, C14: 0.1 µF ceramic disk
C15: 100 µF, 25V electrolytic
Miscellaneous
CON1-CON3: 2-pin connectors
LS1, LS2: 8-ohm, 7-watt speakers with 2-pin connectors
Board: 7 cm x 9 cm Veroboard
Power Source: 12V battery
Heat Sink: For IC STK435
Stereo AF Amplifier with STK435 IC
Fig. 1: Stereo AF Amplifier with STK435 IC

Also Check: Stereo AF Amplifier Using TDA1517

- Advertisement -

Stereo AF Amplifier – Circuit and Working

The circuit diagram of the STK435-based stereo amplifier is shown in Fig. 2. The design includes the STK IC, resistors, and capacitors, with two audio inputs and corresponding amplified outputs for the right and left channels.

Start by completing the connections for the first amplifier section of IC1, referred to as IC1A. Pin 1 connects to two resistors (R2 and R3) in series, followed by a 100-ohm resistor (R5) leading to the +12V supply. A 10µF, 25V electrolytic capacitor (C3) is connected between the junction of R2 and R3 and the ground. A 0.47µF, 25V electrolytic capacitor (C2) connects to pin 1 of IC1, with its negative terminal linked to a 1-kilo-ohm resistor (R1). Additionally, a 470pF ceramic capacitor (C1) connects the negative terminal of C2 to ground.

Pin 2 connects to the ground through an electrolytic capacitor of 220µF, 25V (C4) in series with a 120-ohm resistor (R6). Pins 3, 4, and 8 are also grounded. The output from pin 5 drives an 8-ohm, 7-watt speaker (LS1) via a 1000µF, 25V electrolytic capacitor (C6). The negative polarity of C6 connects to ground through a series arrangement of a 0.1µF capacitor (C14) and a 4.7-ohm resistor (R7).

Pin 6 connects to pin 5 through a 47µF, 25V electrolytic capacitor (C5). Pin 7 is connected to the +12V supply, while pin 9 connects to +12V through a 100-ohm resistor (R5). A 12-kilo-ohm resistor (R8) bridges pins 2 and 5. A 100µF, 25V electrolytic capacitor (C15) connects pin 9 to ground.

The second amplifier section, IC1B, uses pins 10 through 15 and is connected as shown in Fig. 2.

Circuit Diagram for Stereo AF Amplifier
Fig. 2: Circuit Diagram

This circuit operates simply: connect audio inputs (from devices such as laptops, desktops, or MP3 players) to CON1 and CON3, then connect a 12V power supply. The amplified output will be heard through the speakers.

Also Check: Low-Cost Stereo Audio Amplifier Circuit Under 50 Rupees

Construction and Testing

An actual-size single-sided PCB layout for the STK435 amplifier is shown in Fig. 3, with the component layout in Fig. 4. After assembling the circuit on the PCB, enclose it in a suitable cabinet, ensuring proper heat dissipation for the IC with an appropriate heatsink.

Stereo AF Amplifier PCB
PCB design for Stereo AF Amplifier

Alternatively, a 7cm x 9cm Veroboard can be used. Position a 15-pin female connector in the middle of the board, two 2-pin connectors on the far right and left sides, and a 4-pin connector at the bottom. Solder all components as indicated in the circuit diagram, using a low-watt soldering iron. The IC should be inserted after soldering. Connect two 8-ohm, 7-watt speakers to the 2-pin connectors, and supply power using a 12V battery. A clicking sound from the speakers may indicate proper connection.

After assembling on either the PCB or a Veroboard, the device is ready for testing. Gently touch a metal screwdriver to the 2-pin connectors to hear a humming sound from the speakers, confirming functionality. Once tested, connect an MP3 player, laptop, or desktop to the amplifier’s input and enjoy the audio output.


Raj K. Gorkhali is an electronics hobbyist and a regular contributor to EFY

SHARE YOUR THOUGHTS & COMMENTS

×